Showing posts with label network adapter. Show all posts
Showing posts with label network adapter. Show all posts

9/19/2012

Cisco-Linksys PLUSB10 Instant PowerLine USB Adapter Review

Cisco-Linksys PLUSB10 Instant PowerLine USB Adapter
Average Reviews:

(More customer reviews)
I have one computer that has Winme and the other that has XP. I have has these adapters for around 1-2yrs and niether one of my computers ever had a problem with them.

Click Here to see more reviews about: Cisco-Linksys PLUSB10 Instant PowerLine USB Adapter



Buy NowGet 28% OFF

Click here for more information about Cisco-Linksys PLUSB10 Instant PowerLine USB Adapter

Read More...

8/15/2012

Cisco-Linksys WUSB54G Wireless-G USB Adapter Review

Cisco-Linksys WUSB54G Wireless-G USB Adapter
Average Reviews:

(More customer reviews)
I have a SOHO that uses a wired 10/100 switched network. Already part of this network is a Linksys single port Cable / DSL Router. When it came time to make the jump to wireless, the WAP54G seemed the logical choice, as I would not have to reconfigure anything on my existing network. For my initial conversions, I was converting a desktop PC and an older laptop. For this review, I'll be discussing at the WUSB54G. Look for reviews on all these items posted separately.
I decided on the WUSB54G because I did not have any available internal slots. This computer may be replaced in a year or two, and unplugging the network card from a USB port seemed a lot more attractive than opening the case. Actually, the installation is almost a simple as plugging the adapter into an available USB port.
My initial installation was using Version 2.0 of the installation software. The significance of that will be explained later. Regardless of your version of Windows, I suggest installing the software first. This will eliminate any potential problems in the installation process. Make sure you know your network name and WEP Key. You will need to supply that information during installation or you will not be able to connect right away. If you don't have the key handy, it can be input later, but it is not as convenient.
The Wizard does a good job of walking you through each step. Once done, you will need to reboot. Don't disconnect from the wired network just yet. Wait until the next phase is completed. On boot, you computer should detect the new hardware and install the correct drivers for it. The next step could take a while, so be patient. Your new wireless network card will search for a signal, an access point, and you should be prompted when a network is found. If more than one network is detected, a distinct possibility with the proliferation of wireless networks, you will quickly realize the advantages of naming you network something other that the default and of applying a WEP Key to your network.
The initial connection took about two minutes, but seemed a lot longer! You will see an icon on the Bottom Right of the Task Bar indicating you are connected. I do one final check by opening a command prompt and using the command "ipconfig /all" to show all my adapters. If there's a difference in IP addressing ranges, reboot one more time. If both the wired and wireless connections show IP address in the same range, you're ready to unplug the wired connection. Now try opening your web browser. If you can surf, you're all done.
My experience with this installation was very positive. The wizard was friendly, the physical installation could not have been easier, I had all the information on hand I needed and I was wireless after the first reboot. I'm using this adapter with a G network and I'm getting the full throughput.
One final note: this installation went so smoothly I got another adapter from a local dealer that had a price too good to pass up. When I got home, however, I noticed a small sticker that said this was for Windows 2000 and Windows XP only. I then noticed the serial number and installation software said version 1.0. Hmmm... this was going on a Windows 98SE machine. The hardware specs looked identical, from what I could determine from the box, so I tried an experiment and used the version 2.0 software. It worked just fine. BEWARE: this is not an endorsement that this will work in every case nor should you conclude there is no difference between versions. I strongly suggest you try to get the latest version hardware and software for optimal performance.


Click Here to see more reviews about: Cisco-Linksys WUSB54G Wireless-G USB Adapter

Linksys Wireless-G 802.11g 54Mbp USB 2.0 Network Adapter.

Buy NowGet 25% OFF

Click here for more information about Cisco-Linksys WUSB54G Wireless-G USB Adapter

Read More...

2/10/2012

High-Gain USB Wireless N 300Mbps 802.11b/g/n Wi-Fi Network Adaptor With 2 High Gain 5dBi Dipole Antenna - Improving 6X Signal Reception and 3x Speed Review

High-Gain USB Wireless N 300Mbps 802.11b/g/n Wi-Fi Network Adaptor With 2 High Gain 5dBi Dipole Antenna - Improving 6X Signal Reception and 3x Speed
Average Reviews:

(More customer reviews)
I was stuck with the adapter my desktop computer came with... This was fine until I moved into a new apartment building that only had WiFi and I was the furthest apartment away from the source. I had 1-0 bars and constantly lost connection.
I bought this nifty device when I had enough of bad internet. I was skeptical, I had never heard of this particular adapter, and it was selling for basically dirt. I bought it anyway. This adapter improved my signal up to 4-5 bars, and yes, I can see other networks I couldn't before (I even get 4-bar access to the Holiday Inn that is some distance away from me). It's fast and it's reliable.
The adapter came with a CD to install drivers. I didn't bother with it: I had my computer automatically download the drivers and it worked within SECONDS.
Oh: I'm running on Windows 7. It DOES work on Windows 7. The drivers just may not be on the disk. Have Windows search for those drivers instead (with an internet connection, of course).
Fantastic product.

Click Here to see more reviews about: High-Gain USB Wireless N 300Mbps 802.11b/g/n Wi-Fi Network Adaptor With 2 High Gain 5dBi Dipole Antenna - Improving 6X Signal Reception and 3x Speed



Buy Now

Click here for more information about High-Gain USB Wireless N 300Mbps 802.11b/g/n Wi-Fi Network Adaptor With 2 High Gain 5dBi Dipole Antenna - Improving 6X Signal Reception and 3x Speed

Read More...

12/29/2011

Cisco-Linksys USB100TX EtherFast 10/100 USB Network Adapter Review

Cisco-Linksys USB100TX EtherFast 10/100 USB Network Adapter
Average Reviews:

(More customer reviews)
I just received my USB100TX and connected it directly to my TiVo Series 2 with the supplied USB A-B cable. It does *not* come with a CAT-5 UTP Cable, but I have plenty spare and hooked it up. As soon as it was wired to both the TiVo and a hub in my nearby wiring closet the link light was activated. I did not need any of the manuals or driver disks that came in the package.
Within minutes I'd configured my TiVo to recognize the network adapter and my Linksys BEFSR41 Firewall/Router had allocated it a DHCP address.
I immediately ran the test-connection and also forced a daily update.
Downloading schedules are super quick compared to the dialup option. Obviously new firmware updates will also be significantly quicker. Plus the phone line won't be tied up during the call.
I had previously tried a different USB/Ethernet adapter and my TiVo did not recognize it (D-Link USB-650) so beware of using that on a TiVo.
The Linksys USB100TX is the wired adaptor recommended by TiVo and it works perfectly, first time.

Click Here to see more reviews about: Cisco-Linksys USB100TX EtherFast 10/100 USB Network Adapter

The Linksys EtherFast 10/100 USB network adapter allows you to instantly connect to a network from a USB-enabled desktop or notebook PC with Windows 98. The plug-and-play device attaches to any USB-enabled PC or hub (10, 100, or 10/100 Mbps) via a USB type B receptacle. The Linksys EtherFast 10/100 USB network adapter is bus powered, drawing power from the host PC and requiring no external power cords. It features a maximum of 12 Mbps throughput (the maximum supported by USB).
Included with the adapter are a one-year limited warranty and free technical support.

Buy NowGet 68% OFF

Click here for more information about Cisco-Linksys USB100TX EtherFast 10/100 USB Network Adapter

Read More...

11/14/2011

NETGEAR Powerline AV+ 200 Adapter Kit XAVB2501 Review

NETGEAR Powerline AV+ 200 Adapter Kit XAVB2501
Average Reviews:

(More customer reviews)
When I saw this item, I leapt at the opportunity to get my hands on a set of these, in hopes that this Netgear Powerline AV+ 200 Adapter Kit would give me a stronger Internet connection than I was getting wirelessly to my Wii. I've only just recently begun subscribing to Netflix, and the signal that I've been getting wirelessly has left something to be desired with regards to image quality of downloaded media from the Instant queue.
When I received my package, I couldn't wait to get these in place and put them to use. Luckily for me, setting these up was a breeze. The adapters themselves are pretty tall, and fairly wide, as you probably determined by the photo - about 2.5" wide, 5" tall, and about 1.75" deep. They fit VERY snugly into the outlets (I placed each of mine in the bottom outlet, so I could still access the top outlet), so be prepared to apply a little force to the adapters if you're trying to get them into outlets that are in an awkward spot to get to.
The instructions also clearly state that these adapters need to be placed in the wall outlets themselves, NOT into a power strip that items are then connected to. Looking at them, it's pretty obvious to me that the recommendations are wisely made. I simply wouldn't want to fry these adapters out if I put them into an outlet that didn't look adequate for them. So, I unplugged the power strip that I'd had plugged into each outlet that the adapters were going to be occupying, connected one of the enclosed Ethernet cables to each adapter, popped the adapters into the outlets, looked for the LED indicators that showed that these were working well where I'd put them, plugged the power strips into each adapter's built-in outlet (ingenious!), and I was in business! It was then as simple as connecting the Ethernet cable from the adapter near my computer to a port on my wireless router, and then connecting the Ethernet cable from the adapter near my entertainment center to my Wii and its LAN USB adapter, to create the network connection.
When I first got my Wii and was considering my Wii-Internet connectivity options, I'd thought about buying a ridiculously long Ethernet cable to wind around my apartment and its walls, and the challenge it would be to staple/nail around the cord to keep it in place. I could've done that, but I knew how unsightly it would be, so I opted to go for the wireless router that I now have (and still use and enjoy), and connected my Wii to the 'net that way. It was more than adequate, too, until I started my Netflix subscription, and could literally see that my wireless signal was lacking, for Netflix-viewing purposes. Thanks to this adapter kit and a Wii-compatible LAN adapter, though, I've now got the best picture that I've seen on the Netflix Instant queue accessed through my Wii, and a super-strong connection to the Internet with it. Long story short, I couldn't be more pleased by just how well these adapters do what they say they will. I remember originally thinking, "there's no way that these things can make an Internet connection without them being directly connected to each other with a cable." Netgear, you've proven me wrong, and I'm thrilled that you did! Two thumbs up!
* UPDATE*
It's knocking on a year after my install of these NETGEAR Powerline AV+200 adapters, and I'm still happily using them. Perhaps even better, I'm still LOVING them! They continue to provide a strong and consistent signal to my Wii, which I still use daily to watch TV/movies on via Netflix.
If you happen to be having any viewing quality issues, be sure that you've got fast enough Internet service. The NETGEAR adapters will transmit everything they possibly can, as reliably as they can, but if your Internet is just not fast enough, your viewing quality might be a bit on the grainy/pixellated side. I had been using such low-grade Internet when I initially installed these that it wasn't even listed in my cable provider's options - I had to specifically request it in a sales call with them - but I've since bumped my service up to one of the top two options, and that totally fixed the issues that I had with viewing quality.
These NETGEAR adapters were great last May when I first got them, and, eight months later, they're still keeping my entertainment center up-to-date with the latest technology, and doing so beautifully! Good stuff!

Click Here to see more reviews about: NETGEAR Powerline AV+ 200 Adapter Kit XAVB2501

NETGEAR's Powerline AV 200 Adapter extends a high speed Internet connection to any power outlet (2 units required, can purchase 2 unit kit in part# XAVB2001) , Perfect for connecting HDTVs, Blu-ray players, DVRs, PCs and game consoles to your home network and the Internet, Compact design with push-button security, Just plug into any electrical outlet.NETGEAR Green Features: Automatically powers down when not connected or not in use, Disable LEDs to help save energy,Packaging manufactured with at least 95% recycled materials.Disclaimers:1 Requires use of HomePlug AV compatible Powerline devices (two XAV2001 devices included).

Buy NowGet 11% OFF

Click here for more information about NETGEAR Powerline AV+ 200 Adapter Kit XAVB2501

Read More...